![Outlast Q8 Log Oil 5 Gallon Pail](http://timelesswoodcare.com/cdn/shop/products/Q8-5Gallon_21a6bfe2-d039-4ce3-9d3b-fd307c56360e_{width}x.jpg?v=1644868823)
![Outlast Q8 Log Oil 1 Gallon](http://timelesswoodcare.com/cdn/shop/products/Q8-1Gallon_{width}x.jpg?v=1644869707)
![Q8 Log Oil Sample Bottle](http://timelesswoodcare.com/cdn/shop/products/Q8-Sample_{width}x.jpg?v=1645651642)
![Outlast Q8 Log Oil Color Chart](http://timelesswoodcare.com/cdn/shop/products/Q8-Log-Oil-Color-Chart_{width}x.jpg?v=1645651642)
Q8 Log Oil
Water Repellent Wood Preservative
The Q8 log oil is an exterior wood preservative registered with the EPA, specifically designed to control organisms (and mold, termites, beetles) that cause decomposition in log houses and wood paneling. Outlast Q8 log oil provides unsurpassed water-repellent and transparent single-layer trans-oxide paint. Outlast Q8 log oil is a completely exterior treatment that does not create a film and will never crack or peel. The trans-oxide pigment system provides excellent UV control that acts as a sunscreen to slow down the grayness of wood and fade. The solution melts in the wood to provide protection, not only on the surface, but also deep in the structure of the wood cells. Outlast Q8 log oil offers unique flexibility in terms of application temperature range, moisture content in logs and mode of transport. Outlast Q8 log oil meets national VOC requirements. Made in the USA
- Stops decay fungi and mold - Rot control, Toxic to termites and powder post beetles
- Superior water repellency - Controls cracking and splitting
- Easy to apply - One coat coverage - low pressure spray, brush, or roll - low-pressure spray application to refusal
- No lap marks or brush marks - Simple re-coat: no stripping required
- No cob blasting, sanding, or sandblasting needed for re-coats
Outlast Q8 Log Oil should be applied as a single coat initially due to its rapid water repellency, which prevents multiple coats until several years later. Additional coats are recommended every 4-8 years as needed. The oil appears dark at first but lightens to its true color within 48 hours. Caulking or chinking with urethane can be done after 30 days, but with water-based products, it's advisable to wait 60 days in warm weather and 90 days in cooler conditions.
Recommended Application Methods
Brush
Pump Sprayer
Surface Preparation
Surface must be clean and dry
Do not use steel wool or wire brush, Osborn brush recommended
Mildew and mold free
Do not use products containing chlorine bleach
Application Temperature
50° to 90°F
Special Instructions
Back-brushing required for optimal results
Agitate product every 15 minutes
Maintain a "wet edge" to avoid lap marks
Avoid applying product in direct sunlight
Dry Time
Dry to the touch in four to six hours
Complete cure time may take 2 weeks depending on humidity and temperature.
Coverage Rate
125 - 175 square feet per gallon
Recommended Application Methods
Brush
Pump Sprayer
Surface Preparation
Surface must be clean and dry
Do not use steel wool or wire brush, Osborn brush recommended
Mildew and mold free
Do not use products containing chlorine bleach
Application Temperature
50° to 90°F
Special Instructions
Back-brushing required for optimal results
Agitate product every 15 minutes
Maintain a "wet edge" to avoid lap marks
Avoid applying product in direct sunlight
Dry Time
Dry to the touch in four to six hours
Complete cure time may take 2 weeks depending on humidity and temperature.
Coverage Rate
125 - 175 square feet per gallon
Outlast Q8 Log Oil: Wood Preservative & Finish
$92